[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] Re: [FW-1] Secure Client licensing
hi, we use a distributed environment. the relevant lics that we have are: CPMP-ESC-U-DES-V41 - unlimited management CPVP-VFM-250-DES-V41 - firewall/vpn lics (we also have a number of RL type licenses) CPVP-VSC-50-V41 - SC license we also have an SR license, which we have been using without any problems for over a year. When I was implementing Securemote I experimented with SC, but failed to make it work due to the lack of a policy server license. (I couldn't use the management server as a policy server, as there was no FW-1 module installed, and couldn't use the gateways because they didn't have the correct license.) Is it possible that our VAR didn't pass a policy server license on to us!? thanks in advance rich -----Original Message----- From: Mailing list for discussion of Firewall-1 [mailto:[email protected]] On Behalf Of Joe Pampel Sent: 20 May 2002 16:44 To: [email protected] Subject: Re: [FW-1] Secure Client licensing To run SC for v4.1, you should have 3 lic total: Your CPFW-FIG-XXX lic for the FW/internet gateway Your CPVP-VSC-XXX lic for # of secure cleint connections and finally a CPFW-ENC-XXX encryption license which is the Mgt Station piece. do an fw printlic and see what you're missing. If they sold you a VPN setup without the encryption lic, then you should spend some quality time on the phone with your VAR <IMHO. > Joe >>> Richard Marshall <[email protected]> 05/20/02 10:56AM >>> >>> Don, do you know if this is true for all versions of FW-1? I have 'inherited' a 4.1 system. We have an SC license, but no policy server license, and therefore can't use SC until we purchase one. Should I be complaing to our VAR? rich -----Original Message----- From: Mailing list for discussion of Firewall-1 [mailto:[email protected]] On Behalf Of Don Sent: 20 May 2002 14:54 To: [email protected] Subject: Re: [FW-1] Secure Client licensing > I need to know how many license I need for Secure Client. > Our distributor says, that I need only one licence - User license > which contains maximum user count. But I read in CP NG Student book, > that I need two licenses. 1. User license which contains maximum user > count. 2. Policy server license, instaled on firewall module, which > will be act as policy server. You need two licenses. > Is second license for free? It is included in the price of Secure Client. -Don ================================================= To set vacation, Out Of Office, or away messages, send an email to [email protected] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [email protected] ================================================= ================================================= To set vacation, Out Of Office, or away messages, send an email to [email protected] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [email protected] ================================================= ================================================= To set vacation, Out Of Office, or away messages, send an email to [email protected] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [email protected] ================================================= ================================================= To set vacation, Out Of Office, or away messages, send an email to [email protected] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [email protected] =================================================
|