| |
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[FW-1] AW: [FW-1] HA & Stonebeat
- To: [email protected]
- Subject: [FW-1] AW: [FW-1] HA & Stonebeat
- From: "Vogel, Jochen" <[email protected]>
- Date: Tue, 9 Sep 2003 10:12:06 +0200
- Reply-to: Mailing list for discussion of Firewall-1 <[email protected]>
- Sender: Mailing list for discussion of Firewall-1 <[email protected]>
- Thread-index: AcN2JuhMo03X/+HnEdeF7gACpSP7/gAB3v+gAB4VBTA=
- Thread-topic: [FW-1] HA & Stonebeat
hi,
in the gateway cluster object i enabled state sync and
configured the heartbeat net for syncing.
how are the dependencies between the state sync in the
cluster object and the cpconfig option?
thx
jo
> -----Ursprüngliche Nachricht-----
> Von: Burton, Chris [mailto:[email protected]]
> Gesendet am: Montag, 8. September 2003 19:31
> An: [email protected]
> Betreff: Re: [FW-1] HA & Stonebeat
>
> If you are going to use the cluster in a load sharing setup I
> believe it is required or you would have un-synced packets
> being dropped
> on one of the cluster nodes.
>
> You can check to see if the ha/sync module is working
> by issuing
> the following commands on any of the nodes in the cluster,
> since you are
> using a third party clustering solution these do not always show the
> whole truth, but they will tell you if FW-1 is working.
>
> - fw ctl pstat (Check the output at the bottom for sync and ha info)
> - cphaprobe stat (This shows which nodes are currently active)
>
> Chris C. Burton
> Network Engineer
> Walt Disney Internet Group: Network Services
>
>
>
> -----Original Message-----
> From: Vogel, Jochen [mailto:[email protected]]
> Sent: Monday, September 08, 2003 9:33 AM
> To: [email protected]
> Subject: [FW-1] HA & Stonebeat
>
> hi,
>
> i use CP NG FP3 and Stonebeat 3.0 on Solaris 9.
>
> -must the CP HA / State Sync Option in cpconfig be enabled?
> -is there a simple way to control if the sync works?
>
> thx for help
> jo
>
> =================================================
> To set vacation, Out-Of-Office, or away messages,
> send an email to [email protected]
> in the BODY of the email add:
> set fw-1-mailinglist nomail
> =================================================
> To unsubscribe from this mailing list,
> please see the instructions at
> http://www.checkpoint.com/services/mailing.html
> =================================================
> If you have any questions on how to change your
> subscription options, email
> [email protected]
> =================================================
>
> =================================================
> To set vacation, Out-Of-Office, or away messages,
> send an email to [email protected]
> in the BODY of the email add:
> set fw-1-mailinglist nomail
> =================================================
> To unsubscribe from this mailing list,
> please see the instructions at
> http://www.checkpoint.com/services/mailing.html
> =================================================
> If you have any questions on how to change your
> subscription options, email
> [email protected]
> =================================================
>
=================================================
To set vacation, Out-Of-Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
|
|
