[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [FW-1] SecurePlatform - Upgrade to NG FP3
That's what I thought would have to be done. But I wanted to make sure that
a manual install of the linux rpms would work...
And as Damien commented on the same issue, the manuals/docs does leave a bit
to be desired.
Thanks everyone.
Thomas
-----Original Message-----
From: Emmanuel Soremi [mailto:[email protected]]
Sent: 24. oktober 2002 13:43
To: [email protected]
Subject: Re: [FW-1] SecurePlatform - Upgrade to NG FP3
All the CPspupgrade_FP3.tgz does is upgrade the SecurePlatfrom to FP3 (the
Linux OS only), none of the modules are upgraded during this process. You
have to run the install for each of the modules that you have installed,
i.e., SVN Foundation (must be 1st), VPN1/FW1, Performance Pack, Policy
Server, etc etc.
Go to the approaite directory on the CD under the linux dir then run rpm -i
<filename>.rpm
The order I used was:
CPshared-50: SVN Foundation (Do this first!)
CPFirewall1-50: VPN-1/FW-1
CPPerPack-50: Performance Pack
CPPolicySrv-50: Policy Server
Also, when running the rpm command do not use -u for 'upgrade'. It must
actually be installed using the '-i'
It will just sit there for awhile like it is not doing anything, but be
patient, it will come back with a status of the upgrade.
Hope this helps,
-----Original Message-----
From: Thomas Nilsen [mailto:[email protected]]
Sent: 24 October 2002 11:49
To: [email protected]
Subject: Re: [FW-1] SecurePlatform - Upgrade to NG FP3
This is what we did. However, no menu is presented with options. The "patch
add cd" only added a lot of linux related fixes, but not FW1. Trying to run
the same command again returns a message saying there is nothing to
update...
-----Original Message-----
From: Emmanuel Soremi [mailto:[email protected]]
Sent: 24. oktober 2002 12:33
To: [email protected]
Subject: Re: [FW-1] SecurePlatform - Upgrade to NG FP3
It is explained in SecurePlatform User Guide , page 88
Upgrading SecurePlatform Overview
There are two ways to upgrade your SecurePlatform computer:
1 Upgrade from the CD using patch add cd command
2 Upgrade Using SmartUpdate.
Upgrade using the NG FP3 CD
1 Insert the SecurePlatform NG FP3 CD into the CD-ROM drive.
2 Enter the expert mode:# expert
3 Run patch add cd
4 Choose the package you want to install from the menu.
When upgrading from SecurePlatform FP2, the patch command line should be
updated. To do so apply the following steps:
* Mount the CD using the following command:# mount /mnt/cdrom
* Update the patch program by installing the CPpatch_command.tgz package
from the CD:
# patch add /mnt/cdrom/SecurePlatform/patch/CPpatch_command.tgz
Upgrade using SmartUpdate
There are two steps that are needed to upgrade SecurePlatform using
SmartUpdate:
Adding SecurePlatform package to SmartUpdate repository
1 From the main menu choose Products >New Product >Add From CD
2 Choose the CD, and press OK
3 In the Add Product From CD Dialog choose SecurePlatform_AMD, or
SecurePlatform_Intel. These are the packages for AMD and Intel processors.
4 Press OK to add the package you chose to the repository.
Upgrading SecurePlatform
1 Choose the machine you want to upgrade.
2 Right click, and choose Install Product
3 Choose the package you want to install (SecurePlatform_AMD or
SecurePlatform_Intel) and press OK.
-----Original Message-----
From: Thomas Nilsen [mailto:[email protected]]
Sent: 24 October 2002 08:00
To: [email protected]
Subject: [FW-1] SecurePlatform - Upgrade to NG FP3
What is the correct way of upgrading to NG FP3 on a secureplatform
installation? After upgrading the SecurePlatfrom installation to NG 3, a fw
ver still shows that FW-1 is still NG 2.
Best Regards,
Thomas Nilsen
Kverneland IT
Tel: +47 51429463 <> Mob: +47 991 55 001
=================================================
To set vacation, Out Of Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
=================================================
To set vacation, Out Of Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
=================================================
To set vacation, Out Of Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
=================================================
To set vacation, Out Of Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
=================================================
To set vacation, Out Of Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================