| |
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [FW-1] HA in Nokia boxes with NG FP2
- To: [email protected]
- Subject: Re: [FW-1] HA in Nokia boxes with NG FP2
- From: "Roelandts, Guy" <[email protected]>
- Date: Mon, 8 Jul 2002 15:55:52 +0200
- Reply-to: Mailing list for discussion of Firewall-1 <[email protected]>
- Sender: Mailing list for discussion of Firewall-1 <[email protected]>
- Thread-index: AcImg2J0vgsQwbFWTkmQ6wBDUvoGzgAA44yA
- Thread-topic: [FW-1] HA in Nokia boxes with NG FP2
Carlos,
From what I know you should answer Y when asked to install a
Check Point clustering product.
This will trigger the configuration of the new state sync.
When running cpconfig you get also the option to configure
high-availability.
Met vriendelijke groeten - Bien à vous - Kind regards
Guy ROELANDTS
EMEA GS Internet Expertise Centre - CCSE-NG
Compaq BeLux - now part of the New HP
E-mail : [email protected]
Tel: +32(02)729.77.44 (options 3 - 3 - 1)
Fax: +32(02)729.77.65
==========================================================
This message may contain confidential and/or proprietary information,
and is intended only for the person/entity to whom it was originally
addressed. The content of this message may contain private views and
opinions which do not constitute a formal disclosure or commitment
unless specifically stated. Should you receive this message by mistake
please inform the sender immediately.
==========================================================
-----Original Message-----
From: Carlos Infante [mailto:[email protected]]
Sent: 08 July 2002 15:06
To: [email protected]
Subject: [FW-1] HA in Nokia boxes with NG FP2
Hi all,
When configuring the fw modules, NG FP2, for first time or when
running cpconfig you have to choose three options,
"Scanning for unknown interfaces...
Would you like to install a Check Point clustering product (CPHA, CPLS
or State Synchronization)? (y/n) [y] ? n
IP forwarding disabled
Hardening OS Security: IP forwarding will be disabled during boot.
Generating default filter
Default Filter installed
Hardening OS Security: Default Filter will be applied during boot.
This program will guide you through several steps where you
will define your VPN-1 & FireWall-1 configuration.
At any later time, you can reconfigure these parameters by
running cpconfig"
If you want to run VRRP in Nokia Boxes , but you want to have the
firewalls databases synchronized which option should I select? In
Checkpoint Firewall-1 document this step in the cpconfig menu refers to
Cluster XL, but according to above document ClusterXL runs in all
platforms but Nokia.
How does Nokia perform this synchronization in NG?
Is similar to 4.1? (You must edit sync.conf and add the IP of the peer
firewall) If yes, should I ignore the above message and type NO in the
Install Clustering Product menu?
Thanks in Advance
Carlos Infante
=================================================
To set vacation, Out Of Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
=================================================
To set vacation, Out Of Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
|
|
