| |
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [FW-1] nokia 330 boot problems
- To: [email protected]
- Subject: Re: [FW-1] nokia 330 boot problems
- From: Aeon Hale <[email protected]>
- Date: Mon, 4 Mar 2002 11:31:33 -0500
- Reply-to: Mailing list for discussion of Firewall-1 <[email protected]>
- Sender: Mailing list for discussion of Firewall-1 <[email protected]>
- Thread-index: AcHDkhZPKlIRsxTvRqyFWCWHVzGFaQAB8+PA
- Thread-topic: Re: [FW-1] nokia 330 boot problems
i had this problem booting to the bios. All i did was unplug the
console cable when it rebooted and waited about 5 seconds until the box
booted. Then it was fine. Hyperterm was sending the spacebar key to
the console (or TAB) and it was booting to the bio everytime.
-----Original Message-----
From: Mark Ward [mailto:[email protected]]
Sent: Monday, March 04, 2002 10:13 AM
To: [email protected]
Subject: Re: [FW-1] nokia 330 boot problems
the console is working fine. One thing I have noticed is if I power
cycle
the nokia it sends a couple of AT commands through itc console port
before
booting. Can it think its connected to a modem ? If so anybody know how
to
change this.
Mark
----- Original Message -----
From: "Aeon Hale" <[email protected]>
To: <[email protected]>
Sent: Monday, March 04, 2002 2:28 PM
Subject: Re: [FW-1] nokia 330 boot problems
you can jumper pins 2 and 3 on your console cable to "echo" keys on the
hyperterm screen to test if your connecting. Unplug cable from Nokia
and open hyperterminal session. Jumper pins 2 and 3 and then type. iF
your getting text on the screen, the hyperterm session should be fine,
well most of the time.
Hope this helps...
Aeon
-----Original Message-----
From: Geordy Korte [mailto:[email protected]]
Sent: Monday, March 04, 2002 8:16 AM
To: [email protected]
Subject: Re: [FW-1] nokia 330 boot problems
On 04-03-2002 13:38:38 Mark Ward wrote:
>I have received a new Nokia 330 which I am trying to build. I setup the
>initial stuff so I could get on through voyager which worked fine.
However
>when I rebooted through voyager it booted into the CMOS setup for a few
>times.
I had the same problem. It looks like windows 2000 and hyperterm. I
switch to
another term program (MINICOM LINUX) and the problem went away.
--
Kind regards
Geordy Korte
Toshiba Medical Systems Europe
=================================================
To set vacation, Out Of Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
=================================================
To set vacation, Out Of Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
=================================================
To set vacation, Out Of Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
=================================================
To set vacation, Out Of Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
|
|
