| |
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [FW-1] How to set static route table or ip forward on IPSO
- To: [email protected]
- Subject: Re: [FW-1] How to set static route table or ip forward on IPSO
- From: "Roelandts, Guy" <[email protected]>
- Date: Thu, 14 Feb 2002 10:55:34 +0100
- Reply-to: Mailing list for discussion of Firewall-1 <[email protected]>
- Sender: Mailing list for discussion of Firewall-1 <[email protected]>
- Thread-index: AcG1KJmbxB20KBDWRka6pJ4YgKE65AAFETMA
- Thread-topic: [FW-1] How to set static route table or ip forward on IPSO
Liu,
Static routes on IPSO are configured using Voyager, for this\
proceed as follows :
- Login to Voyager
- Click on Config
- Go to Routing Configuration - Static Routes
- Enter the following infos :
- New Static Route : IP address of subnet
- Mask Length : Network mask in # of bits (aka 24 for
255.255.255.0)
- Next hop type : normal
- Gateway type : address
--> click on APPLY
- In the re-generated screen enter the IP-address of the Gateway
then APPLY again
- To make the change permanent click on SAVE
- now from the # prompt of the Nokia a netstat -rn should show
your route
Met vriendelijke groeten - Bien a vous - Kind regards
Guy ROELANDTS
EMEA GS Internet Expertise Centre - CCSA & CCSE
Compaq Software Engineer - Belgium
E-mail : [email protected]
Tel: +32(02)729.77.44 (options 3 - 3 - 1)
Fax: +32(02)729.77.65
==========================================================
This message may contain confidential and/or proprietary information,
and is intended only for the person/entity to whom it was originally
addressed. The content of this message may contain private views and
opinions which do not constitute a formal disclosure or commitment
unless specifically stated. Should you receive this message by mistake
please inform the sender immediately.
==========================================================
-----Original Message-----
From: liu [mailto:[email protected]]
Sent: 14 February 2002 05:09
To: [email protected]
Subject: [FW-1] How to set static route table or ip forward on IPSO
Hi
I am setting a test enviromnent.
210.232.3.1 192.168.2.251
A-----------------firewall--------------------B
A(210.232.3.2)
B(192.168.2.79)
I want to ping HostA from HostB.Impssible.
I can ping 210.232.3.1.So I think it must be problem of route table in
firewall or Nokia OS.
My questions are
Q1.Can firewall do route itself without NAT?
Q2.I stop the firewall and try to do the work by using Nokia OS.I have
using "ipsofwd on admin" command to set up ip forward in Nokia IP330 and
its os is IPSO 3.4.But it still has no function.
Q3.I have seen static route configure at Voyager,but do not know how to
use it. Can someone help me?
Thank you very much.
=================================================
To set vacation, Out Of Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
=================================================
To set vacation, Out Of Office, or away messages,
send an email to [email protected]
in the BODY of the email add:
set fw-1-mailinglist nomail
=================================================
To unsubscribe from this mailing list,
please see the instructions at
http://www.checkpoint.com/services/mailing.html
=================================================
If you have any questions on how to change your
subscription options, email
[email protected]
=================================================
|
|
